Tel:
Email:Address
2/F, Block D, Liye Building, University Science Park, No. 20, Qingyuan Road, Xinwu District, Wuxi city, Jiangsu Province, China. 214000 无锡德盟光电科技有限公司.
Latest products
Efficient application of LED display screen, thorough maintenance and cleaning
by：Demo
2021-07-13
As a medium for indoor and outdoor display, LED electronic display screens will inevitably cause LED display failures due to pollution, looseness, vibration, heat, and large temperature differences during use, which will affect the normal use of the display screen. Therefore, regular display cleaning, maintenance, and maintenance are essential. So what do we mainly do for daily maintenance?
1. Inspection
The general inspection of LED displays adopts the 'monthly inspection system
1. LED display screen body repair, including lamp tube, module, module, power supply, control card;
2. Maintenance of LED display control system, including controller, optical fiber conversion card, distributor, sending card;
3. Special playback operating software for LED display, including maintenance and upgrade of playback software;
4. Regular (once a month) on-site inspection by technicians to check and maintain the system;
5. Support for major events: The company's technical staff guides to ensure the smooth development of on-site activities.
6. For outdoor LED displays, damage caused by natural factors such as wind, rain, thunder, electricity, etc., is not covered by the warranty. The owner needs to purchase insurance from the insurance company, and the insurance company will pay for it.
7. During the maintenance service period, the maintenance problem should be solved within 8 hours for general failures, and no more than 24 hours for major accidents. For repairs that require replacement of modules and other accessories, it should not exceed 24 hours. After the repair is completed, One Service ensures that the large screen does not appear at the module level or above (such as module color cast, module black, one column is not bright, etc.), and it is played normally.
Two, clean up
For display screens with low protection levels, especially outdoor screens, dust in the atmosphere enters the equipment through the ventilation holes, which will accelerate the wear and tear or even damage to equipment such as fans. Dust will also fall on the surface of the internal control device of the display, reducing the thermal conductivity and insulation performance. In humid weather, the dust will absorb moisture in the air and cause a short circuit; it can also cause mildew on the PCB and electronic components for a long time, resulting in a decline in the technical performance of the device. error occured. Therefore, the cleaning of the LED display may seem simple, but it is actually a very important part of the maintenance work.
3. Fastening
LED display is a high power consumption equipment. After running for a long time, due to multiple start, stop and operation, the wiring terminals of the power supply part will be loose due to cold and heat, and the contact will be weak, forming a virtual connection. Heat, even ignite the plastic components next to it. The signal wiring terminals will also become loose due to changes in the ambient temperature, and moisture erosion will cause poor contact, which will lead to equipment failures. Therefore, the LED display connectors must be tightened regularly. When adjusting the fasteners, the force should be even and appropriate to ensure firmness and effectiveness.
Fourth, the surface of the display screen is clean
Visually inspect and inspect the LED display in both the bright screen and the black screen state. Including: Whether the surface of the display screen is contaminated, the purpose is to remove the influence of surface dirt on the luminous characteristics; whether there are damage cracks on the surface of the display screen; whether the communication and distribution cable lines are normal; for the equipment with high protection level, although the high reliability is selected Components and connectors, but the airtightness becomes a key factor. Therefore, it is necessary to regularly check the integrity of the seal; for the outdoor screen steel structure, check the surface paint and rust; for the outdoor screen surface pollution is particularly serious, but also Clean the display surface.
The cleaning of LED display screens is a high-altitude operation, and a professional cleaning team is required. The cleaning operation adopts the high-altitude sling method (commonly known as the spider man) or the hanging blue, equipped with professional cleaning equipment. The cleaning staff chooses different cleaning agents according to the different dirt on the screen to clean in a targeted manner, so as to ensure that the LED tube is not damaged. Complete the cleaning of the LED display screen under the premise of the mask and face mask.
Two points need to be paid attention to during cleaning preparation:
1. Before cleaning, you need to unplug the power cord.
2. The choice of cleaning liquid, cleaning liquid generally includes electrolyte, high-purity distilled water, antistatic liquid, etc., to choose good quality, in order to effectively clean the dust and other stains on the LED screen.
Cleaning and maintenance is divided into three steps:
Step: Vacuum. First suck and sweep away the dirt and dust on the surface of the display mask.
The second step: wet washing. Note that you cannot spray the lotion directly on the screen, but spray a little cleaning liquid on the cleaning cloth, and then gently wipe in the same direction. You can also use the soft brush on the vacuum cleaner to scrub the lamp mask to clean the dirt.
The third step: drying. Use a vacuum cleaner to absorb the water marks left after wet washing to ensure that the display mask is clean and dust-free.
1. Inspection
The general inspection of LED displays adopts the 'monthly inspection system
1. LED display screen body repair, including lamp tube, module, module, power supply, control card;
2. Maintenance of LED display control system, including controller, optical fiber conversion card, distributor, sending card;
3. Special playback operating software for LED display, including maintenance and upgrade of playback software;
4. Regular (once a month) on-site inspection by technicians to check and maintain the system;
5. Support for major events: The company's technical staff guides to ensure the smooth development of on-site activities.
6. For outdoor LED displays, damage caused by natural factors such as wind, rain, thunder, electricity, etc., is not covered by the warranty. The owner needs to purchase insurance from the insurance company, and the insurance company will pay for it.
7. During the maintenance service period, the maintenance problem should be solved within 8 hours for general failures, and no more than 24 hours for major accidents. For repairs that require replacement of modules and other accessories, it should not exceed 24 hours. After the repair is completed, One Service ensures that the large screen does not appear at the module level or above (such as module color cast, module black, one column is not bright, etc.), and it is played normally.
Two, clean up
For display screens with low protection levels, especially outdoor screens, dust in the atmosphere enters the equipment through the ventilation holes, which will accelerate the wear and tear or even damage to equipment such as fans. Dust will also fall on the surface of the internal control device of the display, reducing the thermal conductivity and insulation performance. In humid weather, the dust will absorb moisture in the air and cause a short circuit; it can also cause mildew on the PCB and electronic components for a long time, resulting in a decline in the technical performance of the device. error occured. Therefore, the cleaning of the LED display may seem simple, but it is actually a very important part of the maintenance work.
3. Fastening
LED display is a high power consumption equipment. After running for a long time, due to multiple start, stop and operation, the wiring terminals of the power supply part will be loose due to cold and heat, and the contact will be weak, forming a virtual connection. Heat, even ignite the plastic components next to it. The signal wiring terminals will also become loose due to changes in the ambient temperature, and moisture erosion will cause poor contact, which will lead to equipment failures. Therefore, the LED display connectors must be tightened regularly. When adjusting the fasteners, the force should be even and appropriate to ensure firmness and effectiveness.
Fourth, the surface of the display screen is clean
Visually inspect and inspect the LED display in both the bright screen and the black screen state. Including: Whether the surface of the display screen is contaminated, the purpose is to remove the influence of surface dirt on the luminous characteristics; whether there are damage cracks on the surface of the display screen; whether the communication and distribution cable lines are normal; for the equipment with high protection level, although the high reliability is selected Components and connectors, but the airtightness becomes a key factor. Therefore, it is necessary to regularly check the integrity of the seal; for the outdoor screen steel structure, check the surface paint and rust; for the outdoor screen surface pollution is particularly serious, but also Clean the display surface.
The cleaning of LED display screens is a high-altitude operation, and a professional cleaning team is required. The cleaning operation adopts the high-altitude sling method (commonly known as the spider man) or the hanging blue, equipped with professional cleaning equipment. The cleaning staff chooses different cleaning agents according to the different dirt on the screen to clean in a targeted manner, so as to ensure that the LED tube is not damaged. Complete the cleaning of the LED display screen under the premise of the mask and face mask.
Two points need to be paid attention to during cleaning preparation:
1. Before cleaning, you need to unplug the power cord.
2. The choice of cleaning liquid, cleaning liquid generally includes electrolyte, high-purity distilled water, antistatic liquid, etc., to choose good quality, in order to effectively clean the dust and other stains on the LED screen.
Cleaning and maintenance is divided into three steps:
Step: Vacuum. First suck and sweep away the dirt and dust on the surface of the display mask.
The second step: wet washing. Note that you cannot spray the lotion directly on the screen, but spray a little cleaning liquid on the cleaning cloth, and then gently wipe in the same direction. You can also use the soft brush on the vacuum cleaner to scrub the lamp mask to clean the dirt.
The third step: drying. Use a vacuum cleaner to absorb the water marks left after wet washing to ensure that the display mask is clean and dust-free.
Custom message
